top of page


Public·15 members

Where To Buy Rust Converter

What is Rust Converter? Rust Converter, a water-based primer, contains two active ingredients: Tannic acid and an organic polymer. The first ingredient, tannic acid, reacts with iron oxide (rust) and chemically converts it to iron tannate, a dark-colored stable material. Tannins are a group of water- and alcohol-soluble natural products extracted from fruits, trees and grasses. The second active ingredient is a proprietary organic polymer that provides a protective primer layer. The overall chemical reaction converts rust into a stable, black protective polymeric coating that serves as an excellent primer for both oil and epoxy based paints.

where to buy rust converter


What objects can I use Rust Converter on? Rust Converter can be used on any rusty iron or steel object. It can be used on vehicles, trailers, fences & gates, iron railings and staircases, sheet metal, cast iron, outsides of tanks, lawn equipment, mower decks, farm equipment, tractors to name just a few. It will not work on aluminum, copper, stainless steel or galvanized metal. As a general rule, Rust Converter is a good solution to fixing rust on items you would consider painting.

How do I prepare the surface for application? Good surface preparation will enable the Rust Converter to work effectively and leads to a high quality end result. You will want to remove large rust and scale particles with a stiff bristled brush, hammer or sandpaper. The object of this step is to get any loose or flaking rust off as it does not provide a stable surface. The point is not to remove all the rust (this defeats the purpose of Rust Converter) as Rust Converter chemically bonds to the rust and seals it in. Rust Converter cannot penetrate grease or oil, so clean and degrease the surface first, then let it dry. This step ensures that other surface contaminants will not interfere with the reaction of the rust converter on the rusted surface. If the surface is subject to salt water spray for deicing salts, rinse the surface thoroughly with water, and allow it to dry prior to applying Rust Converter.

Can I apply Rust Converter over non-rusted or painted surfaces? Yes, Rust Converter will adhere to non-rusted or painted surfaces but it does not provide any additional rust prevention when used on these surfaces.

How long does it take Rust Converter to dry? Rust Converter will dry to the touch in approximately 20 minutes. Application of a second coating will ensure proper rust conversion. If possible, wait 24 hours before applying a second coat of Rust Converter to allow for curing. If applying an oil-based top coat, wait 48 hours after the last coat to ensure it has proper time to cure.

Can I put a powder coat over Rust Converter? We have not tested rust converter using a powder coating. From our information, powder coating is not typically applied over a primer coating, but instead is applied over bare metal. We do not know how effective the powder coating would be in adhering to the rust converter product, and it may start to flake off. We do not recommend using a powder coating over the rust converter.

RESTORE METAL SURFACESExtend the life of your metal equipment by protecting it from rust and corrosion. Rust occurs naturally when the iron in steel oxidizes and returns to its original state, iron oxide. Through an innovative chemical conversion process, Corroseal Rust Converter converts rust (iron oxide) into a stable substance, magnetite. It also primes the surface with a high-quality latex metal primer at the same time. Corroseal truly provides one step corrosion control.

RustSeal is a high-performance, single part, ready-to-use, rust preventive coating. RustSeal is impervious to road salts and most every chemical. RustSeal flows out to a beautiful, rock-hard, tough ceramic-like coating that is tough to chip or scratch and will not crack or peel.

RustBlast is a powerful rust remover, zinc phosphate pre-primer, and metal etch. RustBlast effectively dissolves rust, corrosion, metal oxides, and tarnish from most metal surfaces. RustBlast is ideal for removing rust from chrome surfaces.

The Frame Coater Kit is our complete quart size kit that includes enough products to Klean, Blast, and Seal a full-size car or truck frame, or any 50 sq. ft. area with 2 coats of paint coverage and rust protection. You get Top Rated Rust Protection at a tremendous value! Detailed instructions included give you professional results.

SemperForce black nitrile examination gloves are designed for demanding work environments where your safety and comfort are a must. A textured surface promises secure gripping capabilities. SemperForce black nitrile gloves are ideal for automotive, industrial, tattoo, and cosmetology applications.

Restore your investments without breaking a sweat! Gemplers Rust Converter stops your tools, vehicles, tanks and other implements from further rusting. Simply use a wire brush to remove loose or layered scale and rust, then apply Rust Converter with a paint brush or sponge. Once applied, it functions as a primer and the treated surface is ready to paint with an oil-based paint in 48 hours.More Gemplers Rust Converter options: Brush-on formula, 1 gal. (Item # RCG); Aerosol (Item # 127787); Sprayable formula, 1 gal. (Item # 219651); Kits (Item # 230151 & 230152).

The size of the strainer should be relative to the spray nozzle. If you have a 1.4 mil nozzle (ideal); for example, this means that any particle larger than 1.4 mil will clog the gun and adversely affect the performance. Disposable paint strainers are available almost anywhere paint is sold, this would be the preferred recommendation for any spray application.

Exrust penetrates and chemically reacts with rust to quickly remove it from all surfaces. Effective on all ferrous metals without harming the base steel or iron*. After treatment, any type finish can be applied. 50-State VOC Compliant.

Converting rust may be the best solution for you as it halts the rusting process and can be an easier alternative to tackling rust if it is not too thick. For difficult and stubborn rusted areas, you may be better off using rust remover.

The best rust converter for a fast acting, evenly applied solution is the Rust Converter Spray. Our spray rust converter offers long term protection against weather and corrosion. Use our Rust Converter Liquid for more liberal application.

Ferrocon stops the rusting process permanently because it has a 4x lower viscosity than water. It converts the rust into a phosphate coating, which is hard as steel and can never break, peel or come lose from the surface in any way. Paint will stick to this surface much better and longer, then any other conventional primer out there.

Ferrocon is a professional product that primarily is used for removing rust from metal surfaces. With no other comparable product out there. That is why Ferrocon is indispensable for any DIY enthusiasts and professional sheet metal workers.

Ferrocon is a revolutionary product that leaves any conventional product with the same application in its shadow. Ferrocon is a simple, economical, effective and safe rust converter for iron and steel. Ferrocon creates an extremely hard phosphate coating on the surface of the metal, which attaches not only on the surface, but also nestles itself into the micro pores and hairline cracks.

When ferrocon is applied, the coating is also a primer, when compared to traditional primers, Ferrocon has an extremely long adhesion to the finish coating. Therefor, Ferrocon is of great value in the fight against and prevention of rust.

The primer is created by exchange of ions with the metal and forms a barrier for corrosive elements such as water, oxygen, acids, etc. Ferrocon forms a protective layer so we have the perfect primer for any coating (except zinc) which is needed to protect the metal from moisture to prevent rust.

Ferrocon leaves behind an extraordinary steel-hardend permanent coating, that can never break, peel nor crack. It also nests itself in the micro-pores and veins of the metal and because it has a 4x lower viscosity than water, the rusting process can never startup again from the inside out.

Before starting the application, the surface of the metal must be free of obstructing materials such as grease, oil, paint or other covering materials. Also remove loose rust parts. Then apply Ferrocon where it is required. Nu need for grinding or sandblasting.

Note: In order to speed up the de-rusting process, you can heating Ferrocon up in a dip-tank to a max. 176 Fahrenheit. This will dramatically accelerate the reaction time and speed up the whole process.

Ferrocon is ideal in a dip-tank, because the solution can be used over and over again. Not a single spot of rust will remain with this method. Any moving parts such as screw-thread, couplings etc., rinse or wipe off after application. Ferrocon does not react with rubber, so no worries there.

Ferrocon is especially recommended for steel which will come in contact with salt, brine water, seawater, etc. Vessels such as, containers, bridges, pipelines, oil rigs, offshore oil derricks and other offshore structures. Ferrocon is an excellent tool for removing rust. Metal parts can be dipped into Ferrocon without damaging rubber or plastic washers, gaskets or membranes.

CRC Rust Converter is a unique fast drying coating formulated for treatment of lightly rusted or correctly prepared metal surfaces. CRC Rust Converter neutralises rust and converts it to a tough black primer in one easy step. It binds to the surface and provides a waterproof barrier by sealing out moisture and other outside elements for effective long-lasting rust protection. No more sandblasting, heavy scraping, or grinding.

"One Step" Rust Converter killer is a treatment that acts as a rust neutralizer and rust inhibitor and converts it into a smooth long lasting primer on both rust and on metal or previously painted surfaces. This rust killer, converter paint is a water base solution and suitable to paint rusty metal on structures, equipment, vehicles and many other applications. Now in use for over a decade and one of our highest satisfaction rated products. One Step Rust Converter quickly neutralizes and kills rust. Quickly acts as the #1 rust killer on rusted areas. Water based "1" STEP works by a chemical reaction with the rust to kill it dead. One Step The Rust Converter Covers up to 500 sq. ft. per gallon and is touch dry in 30 minutes ready to be top coated 24 hours later or after that.. One Step Rust Converter can be used on surfaces like Iron, Steel, Tin, & Most Galvanized Metals. Not for use on Aluminum ,moving parts like wrenches, inside tanks, stains or heated areas like engines. It prevents the spread of existing rust while also providing a protective coating against the further corrosion of metals. This paint converts the rust into an inert polymer coating, (layman terms - a primer). creates a barrier against moisture and air. It also prevents the formation of new rust. 041b061a72


Welcome to the group! You can connect with other members, ge...
Group Page: Groups_SingleGroup
bottom of page